2000 spiral chute

2000 spiral chute 1. Describing the chute beneficiation process, which includes inclined surface flow sorting steps. The slurry is fed into a inclined chute or slope, and under the push of water, the mineral particle group is loose and layered. The lighter minerals in the upper layer quickly flow out of the groove, while the minerals in the lower layer with a higher specific gravity stay inside the groove or discharge from the bottom at a low speed. After being extracted, the concentrate and tailings are obtained. The spiral concentrator is an equipment for mining and beneficiation, especially ideal for sand mining in coastal areas, riverbanks, beaches, and streams. The equipment has the characteristics of appropriate structure, simple installation, small land occupation, simple operation, stable beneficiation, clear screening of ore, large output, high efficiency, high enrichment ratio, high recycling rate, and reliable operation. There are also advantages such as small weight, moisture resistance, rust prevention, corrosion resistance, and strong adaptability to fluctuations in ore feed volume or concentration, particle size, and grade. 2、 Technical principle: The fiberglass spiral chute mineral separator is not limited to stacking on the cross (or tripod) of the support table. The average mineral mortar is slowly fed onto the spiral groove surface through a feeding groove installed at the end of the rotating groove head for sorting. The tail is equipped with a valve type product selection slot, which divides the selection equipment into three types (or four types) according to grade along the radial direction. Change the cutting width of each product by adjusting the orientation of the valve block. The equipment gathering bucket is a concentric circular tube that allows the obtained multi head ore flow to gather and lead out. The cross section of the spiral chute is particularly suitable for the selection of fine ore particles due to changes in the slope of the curve. 2000 spiral chute 3. Features This machine can be used to separate iron ore, Ilmenite, Chromite, pyrite, zircon ore, Rutile, monazite, ethylene phosphate, tungsten, cassiterite, tantalum, tantalum and niobium from other non-ferrous metal, rare metal and non nonferrous metal ore bodies with different specific gravity. This equipment also has advantages such as stable sorting process, easy operation, wide range of allowable changes in feed density, high enrichment ratio, high recycling rate, small floor area, low water consumption, simple structure, no need for power, large processing output, easy installation, easy operation, low investment, and quick effectiveness. 2000 Spiral Chute 4. The structure of the fiberglass spiral chute is composed of six parts: a feeding homogenizer, a feeding chute, a spiral groove, a product acquisition groove, an equipment gathering hopper or groove bracket (including a cross or triangular frame), and so on. The main component is the rotating groove connected by the rotating disc. The spiral plate is made of fiberglass reinforced coal gangue, and is bolted together. The selection surface of the spiral groove has a pre made durable and wear-resistant layer. He also has the advantages of light weight, firmness, and durability in consumables. The head of the rotating groove is equipped with a multi tube feeding homogenizer to sort minerals evenly, and the control is simple. The concentrator is freely placed on the cross (or tripod) of the support table. The uniform slurry passes through the feeding trough installed on the spiral groove head and slowly feeds onto the rotating groove surface for sorting. The tail end of the spiral groove is installed in a valve block type new product cutting groove, and the sorting equipment is divided into three types (or four types) of new products along the radial direction according to grade. Change the selection width of each new product by adjusting the orientation of the valve block. The new equipment gathering bucket is a concentric circular tube that gathers and leads out the obtained multi-directional mineral flow. The cross section of the spiral concentrator and the slope change of the curve are extremely suitable for the separation of fine particle ore materials. 5、 Scope of use: FRP spiral chute is suitable for separating fine grained iron, ferrotitanium, ferrochrome, pyrite, placer tin, tantalum niobium, gold, coal, monazite, Rutile, zircon, rare earth or other metal and non-metallic mineral materials with sufficient Density contrast. 2000 Spiral Chute 2000 Spiral Chute