Specification parameters of mineral processing spiral chute

The specifications and parameters of the spiral chute for mineral processing are as follows: 1. Overview: The chute sorting belongs to the inclined flow sorting process. The mortar is fed to some inclined grooves or slopes, and with the assistance of water flow, the mineral particles become loose and layered. The upper layer of light minerals are quickly discharged outside the groove, while the lower layer of heavy minerals are retained inside the groove or slowly discharged from the lower part. After each is collected, the selected ore and tailings can be obtained. The fiberglass spiral chute is a mining and beneficiation machine, making it ideal for mining and beneficiation of mineral sand on beaches, river beds, sand banks, and streams. The product has the characteristics of correct structure, simple installation, small footprint, simple operation, stable beneficiation, clear mineral separation, high processing yield, high efficiency, high beneficiation enrichment ratio, high recovery rate, and reliable operation. It has the advantages of light weight, moisture prevention, rust prevention, durability and corrosion resistance, and strong adaptability to fluctuations in feed volume, density, Granularity and grade. 2、 The application method is to erect the spiral concentrator, align it with the vertical line, use an iron frame or wood to stabilize it in a suitable position, and use a sand pump to deliver the ore sand to the two feeding ports above the spiral. The sand is mixed with supplementary water to adjust the density of the ore mortar. The ore mortar naturally swirls from high to low, and there is an inertial centrifugal force in the rotating slope flow rate, which varies in density, specific gravity, particle size, and state of the ore sand, The effect of gravity and centrifugal force is achieved through swirling flow, separating the sand from the ore. The selected ore flows into the concentrate hopper and is piped out, while the tailings enter the tailings hopper and are piped to the sand tank. They are then discharged by a sand pump, completing the entire beneficiation process. The specifications and parameters of the beneficiation spiral chute are three. The characteristics of the spiral beneficiation machine are that it has low power consumption, simple structure, small land occupation, simple operation, stable beneficiation, clear mineral separation, no moving parts, convenient maintenance and management, strong processing capacity per unit area, and other characteristics, which have attracted more attention in many heavy beneficiation machines. Machinery with relatively wide or flat groove surfaces and large areas of laminar flow of mortar are more suitable for processing medium to fine (-4MM) sized ores. China has made spiral chutes with diameters of 400, 600, 900, and 1200 millimeters, Ф The production capacity of 1200mm four heads is approximately 4-6 tons per hour. The specifications and parameters of the beneficiation spiral chute are . The spiral beneficiation machine consists of six parts: a feeding homogenizer, a feeding chute, a spiral groove, an equipment cutting groove, a product gathering hopper, and a groove support (including a cross or triangular frame). The rotating groove connected by spiral blades is a key component. The rotating plate is made of fiberglass (fiberglass reinforced coal gangue) and connected together by bolts. The spiral groove has a pre made wear-resistant layer on the selected surface. She has the advantages of light weight, strength, durability, and the use of consumables. Above the rotating groove is a multi tube ore feeding homogenizer, which distributes ore evenly and has simple control. The mineral separator is not limited to being placed on a cross (or tripod) on a support table. The uniform slurry is slowly fed to the surface of the rotating groove through the feeding groove installed on the spiral groove head, and sorting is carried out. The tail of the spiral groove is installed in the valve type new product acquisition groove, and the selected new products are divided into three types (or four categories) of new equipment along the radial direction according to grade. Change the selection width of each new product by adjusting the orientation of the valve block. The new product gathering bucket is a concentric circular tube that allows the diverse mineral flows obtained to converge and export differently. The cross section of the spiral chute and the different slopes of the curve are particularly suitable for the separation of fine particle materials. 5、 Scope of application The spiral chute can be used to separate fine grained iron, ferrotitanium, ferrochrome, ferrosulfide, tin ore, tantalum niobium, gold ore, coal, monazite, Rutile, zircon, rare earth and other metals and nonferrous metals with a completely different specific gravity. Specification parameters of beneficiation spiral chute Specification parameters of beneficiation spiral chute